-- Curcible Melting Holding Furnace --


Electric Furnace
 
Features:
Special furnace design with heat shield and holding layers for walls.



Heat shield: Heat shielding material is used as lining to reflect electric heat to the crucible directly, so that it can absorb heat immediately without any loss and speed the heating process.



Temperature holding: Thermal isolation material is used as outer lining to ensure optimal temperature holding effect of the furnace for aluminum and power conservation.
 
Control Advantages:




A microcomputer is used for temperature control. The controller is capable of executing automatic PID parameter calculation to ensure that the aluminum is in a constant temperature state and the temperature and quality meet the given requirements.





An SCR phase electric heat controller (electric heat regulator) is used for power control. This controller is controlled by automatic PID parameter calculation and regulates the current by needs. When the aluminum temperature reaches the given value, the SCR will regulate output current. It is a good power saving device.



The timing control is ensured with a 24H Time Setting mechanism. The ON/OFF timing can be pre-set to advance the starting of the furnace and save manpower.





An immersion temperature probe imported from Japan is used to detect aluminum temperature. The temperature probe has a protection tube made of New Ceramics. New Ceramics features high sensing speed with low inaccuracy and is the only material suitable for immersion temperature probes.
The furnace has a liquid leaking & power disconnection alarm device.
The furnace has a strip heater disconnection check device.
Power: 3Φ 220V, 380V or 415V.
     
-- Fuel Melting & Holding Furnace --
 
Features:




Special furnace design with heatproof, holding, and heat shielding layers to ensure optimal thermal isolation. The heat shielding effect is perfect to ensure low temperature of the outer wall, improve working environment, and enhance working efficiency.






The furnace has a heat energy recovery chimney that ensures complete utilization of heat energy and accelerates the melting and holding process. The recovered energy is reused for the second burning without producing any waste gas. The furnace can improve the working environment due to its closed design, heat energy recovery capability and non-noise feature.





The furnace uses Japan KATO automatic diesel burner to ensure high burning efficiency.
Feature: Automatic ignition and temperature control; the high-pressure spray system completely nebulizing the diesel to ensure complete burning, energy saving, and cost reduction.


The 24H Time Setting mechanism can pre-set ON/OFF timing to advance the starting of the furnace and save manpower.





Temperature of aluminum is controlled automatically with an immersion temperature probe imported from Japan. The temperature probe has a protection tube made of New Ceramics (only for graphite crucibles). New Ceramics features high sensing speed with low inaccuracy to ensure constant temperature, high quality and low fail rate of aluminum.
Diesel and kerosene may be used as fuel.
     
-- Graphite Crucible --
產品圖放大
Graphite Crucible
 
 
Features:


Collapse and stripping resistance: High collapse and stripping resistance even at extremely high or low temperatures.


Erosion resistance: The even and seamless inner structure of the crucible is helpful for resistance of erosion against metals and flux.


Impact resistance: Good strength in cold and hot environment to ensure safe operation.



Gasification resistance: The improved crucible material and special coating enhance the gasification resistance and ensure longer service life of the crucible.


Heat conductivity: High content of fixed carbon in the material shortens the melting time and conserves energy.



Non-contamination of metal: The material used is selected under strict criteria without the concern of contaminating metal during the melting process.



Quality stability: The high-pressure one-piece formation technique and the quality guarantee test system ensure the quality stability of the crucible.
.....................................................................................................................................
Specification KW Electric Furnace Crucible (D) mm Crucible (H)mm Furnace (D)mm Furnace (H)mm Suit to die casing machine
Capacity Specification Specification Specification Specification Specification Specification Specification
100kgs 22 HB300HP 525 395 1160 695  
150kgs 28 HB370HP 525 485 1160 785  
180kgs 34 HB450HP 620 510 1260 810 Gavity die casting
250kgs 42 HA600SHP 620 638 1260 940 Gavity die casting
300kgs 47 HA700HP 620 710 1260 1010 Gavity die casting
350kgs 52 HA780SHP 620 810 1260 1110 Gavity die casting
250kgs 45 PB550HP 718 520 1360 820  
350kgs 52 PB620HP 720 600 1360 900 100-150t
410kgs 62 PB750HP 722 690 1360 990 200-250t
500kgs 70 PB800HP 723 750 1360 1050 400t
530kgs 82 PC1100HP 775 750 1420 1050 500t
680kgs 110 PA1330HP 855 740 1500 1040  
750kgs 120 PA1400HP 855 845 1500 1145  
 
Specification Oil FurnaceJapan Burner Crucible (D) mm Crucible (H)mm Furnace (D)mm Furnace (H)mm Suit to die casing machine
Capacity Specification Specification Specification Specification Specification Specification
100kgs GPN20/HB300HP 525 395 1260 820  
150kgs GPN20/HB370HP 525 485 1260 910  
180kgs GPN20/HB450SHP 620 510 1360 935 Gavity die casting
250kgs GPN35/HA600SHP 620 638 1360 1065 Gavity die casting
300kgs GPN35/HA700SHP 620 710 1360 1135 Gavity die casting
350kgs GPN50/HA780SHP 620 810 1360 1235 Gavity die casting
250kgs GPN35/PB550HP 718 520 1460 945 100-150t
350kgs GPN35/PB620HP 720 600 1460 1025 200-250t
410kgs GPN50/PB750HP 722 690 1460 1115 400t
500kgs GPN50/PB800HP 723 750 1460 1175 400-600t
530kgs GPN50/PC1100HP 775 750 1520 1175 650t
570kgs GPN50/PA1200HP 855 740 1600 1280 800t
690kgs GPN75/PA1500HP 855 845 1600 1385 1000t
830kgs GPN75/PA1800HP 855 970 1600 1510 1250t
 
 
Forbes Corporation
Mobile : 886-9-30227668
Tel : 886-2-8811-5809
Fax : 886-2-8811-5765
Add : 1F.,No.38,Ln 156,Shezhong St., Shilin Dist., Taipei City 111 Taiwan